Spektrum SPM18100 DX18 Manual do Utilizador Página 31
- Página / 47
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
31SPEKTRUM DX18 • TRANSMITTER INSTRUCTION MANUAL
EN
Telemetry
Telemetry is in both the system setup and the function list so you
can access the telemetry functions from either list.
You must power off the receiver and transmitter, then power them
both on to reset the telemetry data. You can reset min/max values
by pressing the CLEAR button.
NEVER change Telemetry settings when the aircraft is powered
on. There is a brief interruption in RF output when exiting the
Telemetry screen, and may cause a “Hold” condition.
Custom Voice Setup
Use the custom voice setup function to set up custom voice alerts
or messages. For example, with the custom voice setup function
you can be alerted to a switch change report or a sequence of
alerts using the Stepping Events option. To add a new custom
voice alert or command, enter the Custom Voice Setup function
and select Add New Sound Event with the roller. Select either
Switch Change Report or Stepping Events.
Switch Change Report
Use this feature to have telemetry read in a certain switch
position, current switch position, or a variety of other alerts such
as “Landing Flaps” or “Mix On”. Begin by selecting the switch you
wish to use for the spoken alert, then select the desired setting
next to each switch position.
Stepping Events
Stepping Events can be used to provide voice alerts when a switch
is moved stepping through a list of events. Begin by selecting
the switch desired to trigger each step through the list (when the
switch is triggered as selected, the system will move to the next
item on the list going through the list of user-de ned selections
one by one.) Auto-Cycle can be selected to Inhibit or Active. If
inhibited, the system will go through the list 1 time only, if the
switch is triggered again when at the nal item in the list, it will
not begin at the top of the list. If Active, the system will restart at
the beginning of the list after the last item on the list with the next
switch trigger. Steps is used to select the number of items on the
list for the system to call. This can be set from 0 to 16. So there
can be up to 16 items called to the pilot triggered by the switch
selected. Next select the alert to be spoken for each stepped event
on the list as desired. A variety of alerts can be chosen from the
list including telemetry alerts and a variety of ight conditions and
commands.
System Setup
Press here to enter the System List from the Function list without
turning the transmitter off. A Caution screen will appear that warns
that RF will be disabled (the transmitter will no longer transmit).
Press YES if you are sure and want to access the System List. If
you are not sure, press NO to exit to the main screen and continue
operation.
If you do not press YES or NO, the system will exit to the main
screen and continue operation within approximately 10 seconds.
WARNING: Do not press YES unless the model is turned
off or the model is secured.
- Instruction Manual 1
- Bedienungsanleitung 1
- Manuel d’utilisation 1
- Manuale di Istruzioni 1
- Warranty Registration 2
- General Notes 2
- Pilot Safety 2
- Box Contents 3
- Table of Contents 4
- Transmitter Batteries 5
- Charging Your Transmitter 5
- Transmitter Functions 6
- Navigation 8
- Main Screen 8
- Mode 2 shown 9
- SmartSafe 10
- Failsafe 10
- Hold Last Command 10
- Preset Failsafe 10
- Installation 11
- X-Plus Channels and Failsafe 12
- Installing the SD Card 12
- MODEL TYPE PROGRAMMING GUIDE 13
- COMMON SYSTEM SETUP FUNCTIONS 14
- Spoken Flight Mode Setup 15
- F-Mode Setup 15
- Channel Assign 16
- Channel Input Confi guration 16
- Trim Setup 16
- X-Plus Input Confi guration 16
- Model Utilities 17
- Telemetry 18
- Warnings 18
- Frame Rate 19
- Prefl ight Setup 19
- Trainer 20
- Wireless Trainer 21
- Trainer Alerts 21
- System Settings 22
- Analog Switch Setup 22
- Extra Settings 23
- Serial Number 23
- Calibrate 23
- Transfer SD Card 24
- FUNCTION LIST 26
- D/R & Exponential 27
- Change the offset value 28
- Offset is not 28
- Sequencer 29
- Range Test 30
- Custom Voice Setup 31
- System Setup 31
- X-Plus Monitor 32
- ACRO (AIRPLANE) 33
- Elevon Servo Control 34
- Flap System 34
- ACRO Mixing 34
- Acro Gyro Function 35
- Pitch Curve Function 35
- HELI (HELICOPTER) 36
- Governor 37
- Tail Curve 37
- SAIL (SAILPLANE) 38
- SAIL Mixing 39
- Features: 40
- Receiver Installation 40
- Power System Requirements 40
- Function 41
- TROUBLESHOOTING GUIDE 42
- PARTS LIST 42
- 1-YEAR LIMITED WARRANTY 43
- FCC INFORMATION 44
- FAA INFORMATION 44
- IC INFORMATION 44
- Declaration of Conformity 46
Manuais e produtos relacionados com Painel de controlo Spektrum SPM18100 DX18
(45 páginas)
(45 páginas)
(42 páginas)
(46 páginas)
Painel de controlo Spektrum DX7 Manual do Utilizador
(108 páginas)
(108 páginas)
Samsung CM1069 manuály
Uživatelské manuály a uživatelské příručky pro CD přehrávače Samsung CM1069.
Poskytujeme manuály pdf Samsung CM1069 ke stažení zdarma podle typů dokumentů:
Comentários a estes Manuais