Spektrum DX9 Manual de Instruções Página 11
- Página / 48
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
11SPEKTRUM DX9 • TRANSMITTER INSTRUCTION MANUAL
EN
You establish failsafe positions when you bind your transmitter and
receiver. If the radio signal connection is lost between the transmitter
and receiver, the receiver immediately moves the aircraft control
surfacestothefailsafepositions.IfyouassignthereceiverTHRO
channel to a transmitter channel other than throttle, we recommend
using Preset failsafe with the throttle in the low position.
NOTICE: Failsafe features vary according to receiver. Always consult
the receiver instruction manual for failsafe features.
Before flight, ALWAYS confirm the failsafe functions as you would
expect.
SmartSafe
TM
Failsafe
SmartSafe failsafe is a technology that only acts on the throttle
channel and offers the following benefits:
• Prevents electric motors from operating when the receiver power
is on and the transmitter power is off.
• Prevents the speed controller from arming until the throttle is
moved to the low throttle position.
• Powers off an electric motor and reduces gas/glow engines to
idle if signal is lost.
To Program SmartSafe, move the throttle to the low or off position
before putting the transmitter into bind mode.
To Test the SmartSafe failsafe
1. Power the transmitter and receiver on.
2. Power off the transmitter. The throttle should immediately
move to the failsafe position.
CAUTION: Make sure the aircraft is fully restrained on the
ground. If the failsafe is not set correctly, your aircraft might
advance to mid or full throttle.
Hold Last Command
TheHoldLastCommandfailsafemaintainsthelastcommandon
allchannelsexceptthrottle.Iftheradiosignalislost,theaircraft
maintains the commanded heading until the receiver regains signal.
ToprogramHoldLastCommand,followtheprovidedbinding
instructions in this instruction manual.
To Test Hold Last Command:
1. Power on the transmitter and receiver.
2. Move one of the control sticks to the desired Hold Last
Commandpositionandholdtheinput.
3.Whileholdingthecontrolinput(forexample,asmallamountof
rudder) power off the transmitter. The rudder should maintain
the input command.
CAUTION: Make sure the aircraft is fully restrained on the
ground. If the failsafe is not set correctly, the aircraft throttle
might advance to mid or full throttle.
Preset Failsafe
The Preset failsafe moves all channels to their programmed failsafe
positions.
We recommend using Preset failsafe to deploy spoilers on sailplanes
to prevent a flyaway if the radio signal is lost.
To program Preset failsafe:
1. Insert the bind plug in the bind port on the receiver and power
on the receiver.
2. Remove the bind plug when the orange LED on the main
receiver and all attached remote receivers flash rapidly. The
orange receiver LEDs will continue flashing.
3. Move the transmitter control sticks and switches to the
desired Preset failsafe position. Power the transmitter on.
4. Failsafe programming is complete when the orange LEDs on
the transmitter and all receivers turn solid.
CAUTION: Make sure the aircraft is fully restrained on the
ground. If the failsafe is not set correctly, the aircraft throttle
might advance to mid or full throttle.
PROGRAMMING FAILSAFE POSITIONS
- Instruction Manual 1
- Bedienungsanleitung 1
- Manuel d’utilisation 1
- Manuale di Istruzioni 1
- Manual de instrucciones 1
- Warranty Registration 2
- General Notes 2
- Pilot Safety 2
- Box Contents 3
- DX9 Features 3
- Table of Contents 4
- Transmitter Batteries 5
- Charging Your Transmitter 5
- Transmitter Functions 6
- Navigation 8
- Main Screen 8
- Power System Requirements 9
- SmartSafe 11
- Failsafe 11
- Hold Last Command 11
- Preset Failsafe 11
- MODEL TYPE PROGRAMMING GUIDE 12
- COMMON SYSTEM SETUP FUNCTIONS 13
- Spoken Flight Mode Setup 14
- F-Mode Setup 14
- Channel Assignment 15
- Channel Input Configuration 15
- Trim Setup 15
- MODEL UTILITIES 16
- Warnings 17
- Telemetry 17
- Frame Rate 18
- Preflight Setup 18
- Telemetry Alarms 18
- TRAINER 19
- Wireless Trainer 20
- SYSTEM SETTINGS 21
- Serial Number 23
- Calibrate 23
- TRANSFER SD CARD 24
- FUNCTION LIST 25
- Absolute (Abs.) Travel 26
- D/R & Exponential 26
- Throttle Cut 27
- Throttle Curve 27
- Assigning a Mix to a Switch 28
- Back Mixing 28
- Sequencer 29
- Sequencer SetUp 29
- Range Test 30
- System Sounds 30
- System Setup 31
- ACRO (AIRPLANE) 32
- Elevon Servo Control 33
- Flap System 33
- ACRO Mixing 33
- Acro Gyro Function 34
- Pitch Curve Function 34
- HELI (HELICOPTER) 35
- Swashplate 36
- Governor 36
- Tail Curve 37
- SAIL (SAILPLANE) 38
- SAIL Mixing 39
- Transmitter Mode Conversion 40
- Mechanical Conversion 40
- Re-assembling the Transmitter 41
- Adjust Stick Tension 42
- TROUBLESHOOTING GUIDE 43
- 1-YEAR LIMITED WARRANTY 44
- FCC INFORMATION 45
- FAA INFORMATION 45
- Declaration of Conformity 46
- Instructions for disposal of 46
- Part # 47
- Numéro 47
Manuais e produtos relacionados com Controlos remotos Spektrum DX9
Controlos remotos Spektrum DX18 Manual de Instruções
(47 páginas)
(47 páginas)
Controlos remotos Spektrum DX8 Manual de Instruções
(42 páginas)
(42 páginas)
Controlos remotos Spektrum DX6i Manual de Instruções
(26 páginas)
(26 páginas)
Lenovo H530 Desktop manuels
Manuels d'utilisation et guides de l'utilisateur pour Ordinateurs Lenovo H530 Desktop.
Nous fournissons des manuels en pdf 7 Lenovo H530 Desktop à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentários a estes Manuais